Cake or Pi t-shirt apron

A long time ago I was given a Cake or Pi shirt from shirt.woot. It was size large, which somehow meant it was too big in the body and too small in the neck. I put it in my “refashion or eliminate” bag for later. There are a lot of ways to refashion t-shirts, but most of them assume you want to wear the t-shirt as a shirt. I never wear t-shirts with things printed on them, so there wasn’t much point in restyling it for a shirt for myself. Then, considering the image and size, it occurred to me the shirt could become an apron. And so it did!

modeling apron

I didn’t take any process photos, but here’s how I did it:

  1. apron top Since the accent color of the graphic is blue, I bought matching blue ribbon in two widths and did all stitching in blue thread.
     
  2. The graphic was already more than 12 inches wide, which is wide for an apron top. I basically made the apron as narrow as possible while still preserving the entire image plus a little margin.
     
  3. The graphic was also pretty high. I cut across just under the collar, stitched, and after turning right-side-out to check I stitched diagonally across the corners to cut off as much as possible without crowding the image on the side where it was closer to the corner.
     
  4. This image is properly centered not by taking the full painted region’s width and halving it, but by shifting that toward the larger part of the image. The way it is centered on the apron is not quite right (and I do wish I’d just let the slice’s shadow be cut off). Anyway, that meant the wider part of the apron was limited by the distance to the closer side edge of the t-shirt. I stitched just inside that edge (which was the full distance rounded down to the nearest half inch) and at a matching distance on the opposite side.
     
  5. apron bottom I chose where the apron got wider by seeing how high I could make the wider part without it becoming unreasonably high. To connect the widths I stitched a perpendicular connecting line. I clipped all the corners, pressed the seam allowances open, and turned it right-side-out. I topstitched around the entire apron, which closed the turning opening (the entire bottom of the apron).
     
  6. apron back bottom After cutting the top of the apron I cut the sleeves out just inside their seams. I laid them right sides together, trimmed the curved edges to match, and cut the sides to square them off. I stitched them together on the non-hem sides, clipped the curves, pressed, and turned. To close the hem-edge opening I topstitched. After consideration, I added another line of stitching up the center of the pocket.
     
  7. apron back top T-shirt fabric isn’t the most stable, which is why I stitched the ribbons and pocket through both layers of the apron. My original thought was to have both neck tie and waist tie stitched across the front of the apron, but there wasn’t enough space between the graphic and the top edge to do that. I did stitch the waist tie across the front of the apron, but the neck tie goes across the back (it is still a single length of ribbon, for stability).

That’s it! You can get this apron in my Etsy shop, should you so desire.

Finally pillowfied

Many moons ago I did an embroidery project for the Iron Craft challenge You Are Here, about maps: a topographical map of lips. I didn’t cut the fabric because I had a vision of a pillow, so I folded it up and it lived in various locations for the last two and a half years. Now it looks like this:

bolster main

A bolster pillow! As well as my first invisible zipper. It’s not so invisible because of the pull on the fabric (or maybe because I don’t own an invisible zipper foot), but it’s still better looking than a standard zipper would be.

Sneaking a look inside you’ll find this:

bolster open 1 bolster open 2

A roll of quilt batting, two kinds, that had been sitting on a high closet shelf for nearly as long as the embroidery had been waiting to be made into something. I interleaved the types (the one I had less of, which is completely hidden, was puffier than what you can see), rolled them up, and used an upholstery needle to stitch the edge lightly so it stays put. That made inserting it into the pillowcase easier and means the case can be removed for cleaning if necessary.

The pillow is a bit more than 20 inches long and a bit less than 6 inches across. It will be good for lumbar support or for my husband to put under his knees when he’s napping on his back.

bolster close-up

This was a nice stashbuster! There’s leftover fabric in my fabric stash, but I used about half of the remnant for this, and all of the two pieces of batting. I had to buy a pack of 7 specialty needles to get an upholstery needle, but I’ll have sails to mend soon, right?

Regal tang keychain

Today is my dad’s birthday. Happy birthday, Dad!

But this post has nothing to do with him. I have a couple of friends who have adopted “Just keep swimming” as a mantra, and that inspired me to make a small plush regal tang (also called a blue tang, but that name is used for multiple species) for a keychain.

After looking at Google Images for a while, and then through my fabric stash, I went to the store, made a couple of versions, and ended up with this:

regal tang

An amalgam of craft techniques are represented. Although the felt is acrylic, I needle-felted the tail and fins onto the body, with some extra wool on top. The eyes are shank buttons pushed through a small slit in the body felt, with a second button on the inside of each to keep them from pulling out again. I had to hand-sew the region nearest the eye, but the rest of the perimeter was sewn by machine. After trimming my seam allowance –perhaps past the best point– I painted the navy blue details and dripped some Fray-Check on the stitching that wasn’t painted. I opened a small hole for the keyring with a large needle.

It’s pretty substantial for a keychain, but it could be hung up elsewhere too.